How to Attach a Popsocket (phone holder)

Attach the Popsocket Grip

Buy popsockets from the brand's official website. You can choose from many different colors and designs. You can also design your own popsocket by uploading a unique photo while placing your order.

To order a popsocket, visit https://www.popsockets.com/.

Decide where to mount the popsocket. Decide in advance where you want to mount the popsocket according to your intended use. Place the popsocket on the back of the phone without removing the adhesive to see how it looks. If you want to attach two popsockets to the back of your phone, try placing them on and making sure they are lined up.

For example, if you want to support a small phone vertically, place the popsocket at the bottom of the phone.

You can attach two popsockets to support larger phones or to wrap headphones neatly.

Decide whether you want to attach the popsocket directly to the phone or to the case.

Peel off the sticker on the adhesive surface. When ready to attach the popsocket, slowly peel off the sticker on the base. Gently pull the patch to avoid tearing, starting from one corner and gently lifting it up. Do not remove the adhesive protection layer before you are ready to attach the popsocket to your phone.

Paste the popsocket into the phone. Once the adhesive surface is peeled off, press it onto the location where you want to place the popsocket. Press down firmly for 10-15 seconds to make sure it sticks to the phone.

Reposition the Popsocket Grip

Flatten the popsocket before removing it. Press down to flatten the popsocket on the back of the phone. This will make it easier to remove the popsocket. Do not attempt to remove the popsocket while it is extended, as the popsocket may separate from the base during removal.

Gently separate the popsocket from one corner. Choose a corner of the popsocket and start gently peeling it off. Continue to gently pull in a circular motion, pulling up the outer surface. Once the entire circle around the popsocket has come off, pull the popsocket up to remove it.

Use dental floss to remove the popsocket if you can't pull it out. If the adhesive is too tight and you can't remove the popsocket by hand, slide the dental floss underneath the holder to peel it off. Wrap both ends of a long piece of dental floss around your index finger and place it on one edge of the popsocket. Gently pull the dental floss tightly between the popsocket and phone, removing the adhesive layer.

Wash and dry the popsocket if the adhesive part is dirty. Make sure the adhesive part of the popsocket is always clean so it can stick back to its original state. Rinse under cold water and leave for 10 minutes to dry. You should attach the glue to another surface within 15 minutes, otherwise the glue will dry.

Stick the popsocket onto a new surface. Select the new location to mount the popsocket, either on the old phone or on the new phone. Press down firmly on the popsocket so that the adhesive adheres firmly to the phone. Continue pressing on the popsocket for 10 - 15 seconds to ensure it is completely adhered.

Attach the popsocket retaining clip

Buy a popsocket holder from the company's website. The retaining clip can be found in the "accessories" section. The popsocket holder can be attached to surfaces such as your car dashboard or your bedroom mirror.

Buy a popsocket holder at https://www.popsockets.com/.

You can also purchase popsocket clips designed to attach to your car's air vents.

Clean the adhesive surface with alcohol. Make sure the surface of the popsocket holder is clean so it can adhere well. Put a few drops of alcohol on a cotton ball or use an alcohol-soaked antiseptic wipe to clean the area where the clip will be attached. The surface will dry in seconds.

Remove the film from the adhesive on the base of the retaining clip. Gently remove the adhesive protective film on the popsocket holder. Try to avoid touching the adhesive layer. The 3M VHB pad is designed with high adhesion and will be difficult to remove from the skin if you accidentally touch it.

Press the clamp down onto the adhesive surface and let it bond for 8 hours. Press the adhesive portion of the retainer down onto the surface you are planning to apply. Press firmly on the clamp for 10-15 seconds. Allow the clamp to bond to the surface for 8 hours before use to ensure it is securely attached.

The popsocket holder can only be attached once, so determine the position very carefully before attaching.