How to Crimp Rj45

You can quickly and easily crimp an RJ-45 to a cable with or without a crimping tool. If you have a crimping tool, strip away a portion of the sheath, untangle and arrange the wires in the correct order, fit them into the connector, and...

Method 1 of 2:

Using a Crimping Tool

  1. Picture 1 of How to Crimp Rj45
    Strip the cable back 1 inch (25 mm) from the end. Insert the cable into the stripper section of the tool and squeeze it tight. Then, rotate the crimping tool around the cable in a smooth and even motion to create a clean cut. Keep the tool clamped and pull away towards the end of the wire to remove the sheathing.[1]
    1. The stripping section is a round hole near the handle of the tool.
    2. The sheathing should come off cleanly, leaving the wires exposed.
  2. Picture 2 of How to Crimp Rj45
    Untwist and straighten the wires inside of the cable. Inside of the cable you'll see a bunch of smaller wires twisted together. Separate the twisted wires and straighten them out so they're easier to sort into the right order.[2]
    1. Cut off the small plastic wire separator or core so it's out of the way.
    2. Don't cut off or remove any of the wires or you won't be able to crimp them into the connector.
  3. Picture 3 of How to Crimp Rj45
    Arrange the wires into the right order. Use your fingers to put the wires in the correct order so they can be properly crimped. The proper sequence is as follows from left to right: Orange/White, Orange, Green/White, Blue, Blue/White, Green, Brown/White, Brown.[3]
    1. There are 8 wires in total that need to be arranged in the right sequence.
    2. Note that the wires labeled Orange/White or Brown/White indicate the small wires that have 2 colors.
  4. Picture 4 of How to Crimp Rj45
    Cut the wires into an even line 1⁄2 inch (13 mm) from sheathing. Hold the wires with your thumb and index finger to keep them in order. Then, use the cutting section of the crimping tool to cut them into an even line.[4]
    1. The cutting section of the tool will resemble wire cutters.
    2. The wires must be in an even line to be crimped into the RJ-45 connector properly. If you cut them in an uneven line, move further down the wires and cut them again.

    Tip: If your tool doesn't have a cutting section, use a pair of wire cutters or scissors to cut the small wires.

  5. Picture 5 of How to Crimp Rj45
    Insert the wires into the RJ-45 connector. Hold the RJ-45 connector so the clip is on the underside and the small metal pins are facing up. Insert the cable into the connector so that each of the small wires fits into the small grooves in the connector.[5]
    1. The sheathing of the cable should fit just inside of the connector so it's past the base.
    2. If any of the small wires bend or don't fit into a groove correctly, take the cable out and straighten the wires with your fingers before trying again.
    3. The wires must be inserted in the correct order and each wire must fit into a groove before you crimp the connector.
  6. Picture 6 of How to Crimp Rj45
    Stick the connector into the crimping part of the tool and squeeze twice. Insert the connector in the crimping section of the tool until it can't fit any further. Squeeze the handles to crimp the connector and secure the wires. Release the handles, then squeeze the tool again to make sure all of the pins are pushed down.[6]
    1. The crimping tool pushes small pins in the grooves down onto the wires to hold and connect them to the RJ-45 connector.
  7. Picture 7 of How to Crimp Rj45
    Remove the cable from the tool and check that all of the pins are down. Take the connector out of the tool and look at the pins to see that they're all pushed down in an even line. Lightly tug at the connector to make sure it's attached to the cable.[7]
    1. If any of the pins aren't pushed down, put the wire back into the crimping tool and crimp it again.
Method 2 of 2:

Attaching RJ-45 Connectors without a Crimping Tool

  1. Picture 8 of How to Crimp Rj45
    Cut into the outer sheath of the cable with a pair of scissors. Take a pair of scissors and gently cut into the plastic sheath about 1 inch (25 mm) from the end of the cable. Make sure you don't cut into the wires inside. When the scissors penetrate the sheath, rotate the cable and scissors to create a cut around the cable. Then, stick your fingertips under the sheath and pull it off towards the end.[8]
    1. Don't cut too deep when you make your initial incision.

    Tip: If you don't have scissors, you can use a utility knife to cut away the outer sheath. But be careful not to cut the wires inside.

  2. Picture 9 of How to Crimp Rj45
    Separate and straighten out the small wires in the cable. Use your fingers to untwist and straighten the exposed wires after you remove the sheath. If there is a plastic core or wire separator, cut it away with your scissors.[9]
  3. Picture 10 of How to Crimp Rj45
    Put the wires in the right order. Arrange the wires from left to right so the order is orange/white, orange, green/white, blue, blue/white, green, brown/white, brown. They need to be arranged in a specific order to be properly crimped to the RJ-45 connector.[10]
    1. Some of the wires have 2 colors on them, like the orange and white wire.
  4. Picture 11 of How to Crimp Rj45
    Trim the wires 1⁄2 inch (13 mm) away from the sheath. Bring the wires together and hold them with your thumb and index finger. Then, use your scissors to cut them. Make sure they're cut evenly.[11]
    1. The wires need to be even in order to fit into the grooves in the connector.
    2. If you cut the wires unevenly, move further down and cut them again so their ends are in a straight line.
  5. Picture 12 of How to Crimp Rj45
    Fit the wires into the grooves of the RJ-45 connector. Hold the connector so the metal pins or brackets are facing up and the clip is facing down. Hold the small wires together in the right order and slide them into the connector. They should fit into the grooves of the connector, with the end of the sheath of the cable fitting just past the base of the connector.[12]
  6. Picture 13 of How to Crimp Rj45
    Press the pins down with a flathead screwdriver. Locate the small metal pins at the ends of the grooves of the connector. Use a thin, flathead screwdriver to push each of the pins down. Push the pins 1 by 1 so they're pressed all the way into each wire.[13]
    1. Be careful not to crack or break the plastic connector.
  7. Picture 14 of How to Crimp Rj45
    Tug on the end of the connector to make sure it's secure. Double check that all of the pins are pressed into the wire, and give a light tug on the connector to make sure it won't slide off. Each of the pins should be inserted at the same level to form an even line.[14]
    1. Lightly shake the cable and listen for any rattling that could indicate that one of the pins isn't secure.
Update 04 March 2020
wiresconnectorcutcable

You should read it

Maybe you are interested

Category

System

Mac OS X

Hardware

Game

Tech info

Technology

Science

Life

Application

Electric

Program

Mobile