HomeSystemConfigure Router SwitchHow to login to TP-Link's Wireless Access Point management

How to login to TP-Link's Wireless Access Point management page

A low version of the web browser may cause compatibility issues with the web-based interface (management page) of the device, such as being unable to log into the interface, rendering incomplete features, etc. It is recommended that you use a wired connection, if you plan to change your device's wireless settings or upgrade the firmware version.

Note: For products with DHCP enabled by default, not listed below, please refer to this link here.

This article applies to wireless access points and extenders with DHCP disabled by default. (TL-WA500G, TL-WA501G, TL-WA601G, TL-WA701ND v1, TL-WA801ND v1, TL-WA901ND v1 / v2, Tl-WA730RE, TL-WA5110G, TL-WA5210G, TL-WA7210N V1, TL-WA7510N , TL-WA830 v1 / v2 of the old version).

Before logging into the web-based interface, you need to assign a static IP address on your computer.

Step 1 : Connect your computer to the TP-Link LAN port with an Ethernet cable.

Step 2 : Assign a static IP address manually on the computer.

The article takes Windows 7 as an example:

1. Left-click on Start> Control Panel> Network and Internet> Network and Sharing Center> Change Adapter Settings (on the left menu).

2. Right click on Local Area Connection and go to Properties . Then double-click on Internet Protocol Version 4 (TCP / IPv4) .

How to login to TP-Link's Wireless Access Point management page Picture 1

3. Set a static IP address (for example choose 192.168.1.x ). If your AP is 192.168.0.254 , set the static IP address to 192.168.0.X.

How to login to TP-Link's Wireless Access Point management page Picture 2

Note:

LAN IP varies by model. Please find it on the bottom label of the product.

Step 3:

Open a web browser and enter the IP address of the access point / extender (default is 192.168.1.1/192.168.1.254/192.168.0.254 ) in the address bar and press Enter.

How to login to TP-Link's Wireless Access Point management page Picture 3

Step 4:

Enter the username and password in the boxes of the login page, the default username and password are both admin , then click OK.

How to login to TP-Link's Wireless Access Point management page Picture 4

Note:

1. The above IP settings are used to login to TP-Link's web-based interface for configuration.

2. If you have a broadband router providing Internet connection, reconfigure the computer's IP settings to Obtain an IP address automatically & Obtain DNS Server address automatically .

How to login to TP-Link's Wireless Access Point management page Picture 5

Reconfigure the computer's IP settings to Obtain an IP address automatically & Obtain DNS Server address automatically

5 ★ | 1 Vote
TP-Link

You should read it

May be interested

  • How to configure Xiaomi 3C WiFi router to be repeaterPhoto of How to configure Xiaomi 3C WiFi router to be repeater
    if you are facing wifi signal range problem indoors and office areas, the range of the main wifi router is low. you can increase the wifi range by using mi 3c's repeater mode setting without changing the main wifi name and password.
  • How to configure the MikroTik routerPhoto of How to configure the MikroTik router
    if you are familiar with these routers, you probably know that they are built using the mikrotik routerboard hardware platform, powered by mikrotik routeros operating system - but, how about configuring these routers? here's an overview guide to get you started!
  • How to connect a Linksys router to another routerPhoto of How to connect a Linksys router to another router
    cascading is a term used when connecting one router to another. in this case, the first router could be linksys or another provider and is called the primary router. the second router must be from linksys and called the secondary router.
  • Set up the Linksys router with a static IP addressPhoto of Set up the Linksys router with a static IP address
    a static ip address is a fixed ip address configured in the settings of your computer or router. some internet service providers (isp) require you to enter a static ip address on your computer or the tcp / ip settings of your router to be able to connect to the internet.
  • How to use the backup and restore feature in the Linksys routerPhoto of How to use the backup and restore feature in the Linksys router
    in the case when you need to reset the router to factory default settings, you will be able to restore the previous configuration with a backup configuration file. to backup and restore router configuration, follow the instructions below.
  • How to replace WiFi antenna on wireless routerPhoto of How to replace WiFi antenna on wireless router
    when the router is installed in the center of a house and wireless clients are distributed throughout the rooms, a omnidirectional antenna will transmit signals to all corners of the house.

Configure Router Switch