How to Do a Burnout on a Motorcycle

A burnout, also known as peeling out, is when you spin the wheels of a motorcycle while keeping the frame of the bike stationary. You can use a burnout to create a big cloud of smoke and impress your friends, but over time, it can damage...

Part 1 of 2:

Applying the Brake

  1. Picture 1 of How to Do a Burnout on a Motorcycle
    Stand with both feet as flat on the ground as possible. To prevent the tires from gaining traction, put the least amount of weight on the bike by standing over the bike. If the tires have too much traction, then the motorcycle will move forward when you attempt a burnout.[1]
  2. Picture 2 of How to Do a Burnout on a Motorcycle
    Start the motorcycle and keep it in the neutral gear. Turn the key in the ignition and start up the engine so it can warm up. Check the temperature gauge after a few minutes to make sure the dial is at about the halfway point to indicate that the engine has warmed up.[2]
    1. Keep the engine in the neutral gear while it warms up.
    2. You can rev the engine a few times to get it warmer faster.
    3. Allow the engine to run for at least 5 minutes before you attempt a burnout.

    Warning: It's dangerous to perform a burnout with a cold engine because it can sputter and suddenly gain traction, causing the motorcycle to lurch forward.

  3. Picture 3 of How to Do a Burnout on a Motorcycle
    Pull the clutch lever all the way in. On most motorcycles, the clutch is the lever on the left hand of the handlebars. Use all 4 fingers to engage the clutch by pulling it back all the way to the handlebar.[3]
    1. Keep a tight grip on the clutch lever so it stays engaged.
    2. If your motorcycle has the clutch on the right handlebar, be sure to engage it fully with all 4 fingers of your right hand.
  4. Picture 4 of How to Do a Burnout on a Motorcycle
    Hold the front brake with the middle finger of your right hand. Apply the brake and rev the engine throttle simultaneously by holding the front brake with your right hand. Use just your middle finger to pull back the lever for the brake so you can use the rest of your hand to work the throttle.[4]
    1. If you have a motorcycle with the throttle on the left-hand side, then use the middle finger of your left hand to apply the brake.
Part 2 of 2:

Releasing the Clutch

  1. Picture 5 of How to Do a Burnout on a Motorcycle
    Put the motorcycle into first gear. Use your foot to click the gear shift pedal so the motorcycle shifts into first gear. Keep the clutch engaged with your left hand so the motorcycle doesn't shift into gear yet.[5]
  2. Picture 6 of How to Do a Burnout on a Motorcycle
    Rev up the engine close to the red line on the gauge. With your right hand, rev up the engine by twisting the throttle down. Look at the repetitions per minute (RPM) gauge and look for the red line towards the top of it. Rev up the engine so the arrow is about 75% of the way to the red line at the top.[6]
    1. Start revving the engine slowly to make sure the engine isn't in gear and the bike won't move.
    2. It's important that you build up the engine before you put it into gear so the tire spins too fast to gain traction.
  3. Picture 7 of How to Do a Burnout on a Motorcycle
    Lean forward slightly to shift all of the weight off of the rear tire. Make sure your feet are flat and you're standing stable. To make sure that all of the weight is off of the rear tire, lean forward a little bit.[7]
  4. Picture 8 of How to Do a Burnout on a Motorcycle
    Let go of the clutch to perform a burnout. Don't ease off of the clutch to disengage it. Instead, let it go in 1 motion by releasing all of your fingers at once. The engine will then engage in first gear and the rear tire will start spinning to create a burnout.[8]
    1. The longer you hold the burnout, the more wear and tear on your rear tire.

    Tip: Hold the burnout for a minute to create a plume of smoke.

  5. Picture 9 of How to Do a Burnout on a Motorcycle
    Reengage the clutch and release the throttle to end the burnout. Use your left hand to pull the lever to engage the clutch, which will pull the engine out of first gear and into neutral. Rollback the throttle with your right hand, but keep the brake engaged the entire time. The rear tire will come to a stop and your motorcycle will not roll forward.[9]
    1. Do not release the brake until the tire has completely stopped spinning.
Update 24 March 2020
enginehandclutchgear

You should read it

Maybe you are interested

Category

System

Mac OS X

Hardware

Game

Tech info

Technology

Science

Life

Application

Electric

Program

Mobile