How to clear the drain hose when clogged with vinegar simple and effective

If during use it is found that the water in the bath or wash basin drains very slowly, maybe your house is blocked. The main cause is due to hair loss, soap bubbles and garbage after months of use or because of unintentional dumping of waste water into pipes, allowing grease to stick to the inside of the pipe. When the sewer pipe is clogged, in addition to causing sewage to escape quickly, it also makes the bathroom smell very uncomfortable. This must not be too strange for us, so you should not be too confused. Instead of having to spend money to call a plumber to repair it, you can first clear the pipes yourself with substances available in the house. Vinegar, baking soda, borax and hot water are simple but very effective substances to clear water pipes that are clogged with slow drainage. Invite you to consult!

Method 1: Prepare the culvert mixture

1. Drain the water in the sink or bath

If you notice the discharge of water in the bath or sink is too slow, you may have to wait a while. However, if the water is completely drained, the plumbing mixture will work more quickly and efficiently.

2. Use the cleaners available in the kitchen

There are many options for making homemade drain and create a chemical reaction when combined. Most are related to the same type of vinegar to create a chemical reaction when combined. Check if you have the following drain switches:

1. Vinegar ( white vinegar or apple cider vinegar ) is the basic acid solution that causes a foaming reaction.
2. Lemon juice is an acidic, vinegar-like substance that has a cooler aroma.Lemon juice is an appropriate option to clean the sink in the kitchen.
3. Baking soda powder is often used as a versatile cleanser.
4. Salt helps to erode the blockage in the tube.
5. Welding is often used as a general purpose detergent.

3. Pour vinegar and other substances to drain the drain pipe

No need to mix substances before pouring, the mixture will foam itself and chemical reaction occurs.

1. For baking soda and vinegar mixtures: use 1/2 cup of baking soda and 1/2 cup of white vinegar.
2. For lemonade and baking soda: use 1 cup of baking soda and 1 cup of lemonade.
3. For salt, borax and vinegar mixtures: use 1/4 borax cup, 1/4 cup of salt and 1/2 cup of vinegar.

Method 2: Impact on the switch point

1. Close and leave the mixture in place

You can use a water hose stopper or a cloth with hot steam to seal the pipe. Seal the pipe within 30 minutes. At this time, the foam will work to corrode the switch.

2. Vacuum the pipe

Use a small rubber catheter to fit the size of the sink to create an impact on the clogged material. Seal and press the rubber tip down the drain hose and push the tool up and down.

1. The catheter is most effective when filling the bath or sink with water.Water will increase the pressure and make the switch point.

3. Use the hook to pull the garbage out of the switch

If the duct is blocked by hair, use a metal hook and break into a long metal wire with a small hook at the top. Carefully thread the hook end of the metal wire into the pipe. After that, spin the hook to remove all the trash. When the garbage is caught in the hook, gently unplug it.

1. Pay attention not to scratch the metal bath or sink.Moreover, you should also be careful when bending or bending by very sharp metal.

4. Use a wire pipe interlock tool

The wire pipe interlock tool is shaped like a long piece of metal rope. You need to carefully insert this tool into the drainage pipe. When the string is stuck, turn the rope lightly so that the garbage in the tube gets into the wire, then slowly pull the cord out, the water pipe will be cleared. Then rinse and repeat the process.

1. Protective gloves should be worn by metal tools that can be very sharp and prepare an old towel, a small bucket for storing garbage in the pipe.This metal bar can be very sharp.

Method 3: Drain the pipe

1. Drain the pipe with hot water

Boil at least 6 cups of hot water or a full kettle. Open the lid and slowly pour hot water down the pipe.

1. Note if your home uses plastic pipes, do not use water that is too hot and avoid boiling water into the pipes.

2. Repeat the process

If the water is still draining slowly, repeat the process until the water can completely drain.

1. If the water is still not drained, there is a possibility that a lot of hair gets in the pipe.Therefore, manual operation may be required to clear the switch.Besides, you should call a plumber, especially if the tube completely stops flowing.

3. Use gravity and pressure to discharge the pipe

This is best suited for drainage pipes in the bathtub because you can fill dozens of liters of water into the tub. In addition, flush hot water into the tank then open the drain cover and allow the pressure of the water to block the switch.

Refer to some more articles:

1. 7 cleaning products should never be mixed together
2. 9 great home cleaning techniques save time
3. 13 great uses of PAPER you may not know

Having fun!