Jonas Jackel
Owner, Huckleberry Bicycles
How to Adjust Bike Brakes
Routinely adjusting your bike brakes will help them perform better and ensure you're riding safely. The two main things you'll want to adjust in your bike's brake system are the brake pads and the brake cables. Worn down brake pads that...
Method 1 of 2:
Adjusting Your Brake Pads
-
Picture 1 of How to Adjust Bike Brakes Check your brake pads before you make any adjustments. The brake pads are the pads that clamp down on the front tire of your bike when you pull the brake lever. If the brake pads are worn down past the line labeled 'wear line,' you'll need to replace them before you make adjustments to your brakes.[1]- If the wear lines on your brake pads aren't labeled, they should be marked by grooves on the side of the pads instead.
- You can order new brake pads online or pick some up at your local bike shop.
-
Picture 2 of How to Adjust Bike Brakes Squeeze the brake lever to see where the pads hit the rim. Both brake pads should be coming into contact with the rim of the front tire at the same time. They should be hitting the center of the rim, with an equal amount of space above and below the pad. If the pads are hitting the rim too high or low, they could come into contact with the rubber part of the tire or the spokes on the bike.[2]- Crouch down to get a good look at the brake pads as you're squeezing the brake lever.
-
Picture 3 of How to Adjust Bike Brakes Use an Allen wrench to loosen the bolts holding the brake pads in place. Turn the Allen wrench counterclockwise to loosen the bolts. Don't loosen the bolts all the way or the brake pads will come out of the brake pad holder.[3] -
Picture 4 of How to Adjust Bike Brakes Move the brake pads up or down in the brake pad holder. They should easily move up and down once the bolts are loosened. If the pads were too low on the rim, move them up until they're centered. If the pads were too high on the rim, move them down until they're centered.[4] -
Picture 5 of How to Adjust Bike Brakes Re-tighten the brake pad bolts with the Allen wrench. Keep turning the Allen wrench clockwise until the bolts are fully tightened. Check to make sure the brake pads are centered. Readjust if needed.[5]
Method 2 of 2:
Tightening Your Brake Cables
-
Picture 6 of How to Adjust Bike Brakes Test the tightness of your cables by pulling each brake lever. When you pull the brake levers, they should be about 1 ½ inches (3.8 cm) away from the grip on the handlebars. If the levers hit the handlebars when you pull them, the brake cables are too loose.[6] -
Picture 7 of How to Adjust Bike Brakes Loosen the barrel adjusters for minor brake cable adjustments. If your brake cables are just slightly loose, loosening the barrel adjusters might fix the problem. The barrel adjusters are located where the brake cables meet the brake levers.[7]- Loosen the barrel adjuster attached to the loose brake cable by turning it counterclockwise. Loosening the barrel adjuster will actually slightly tighten the brake cable.
- After you loosen the barrel adjuster, pull the brake lever to see if it fixed the problem. If the brake cable is still too loose, you'll need to adjust it on the caliper. Leave the barrel adjuster as it is. Don't tighten it yet.
-
Picture 8 of How to Adjust Bike Brakes Unscrew the bolt holding the brake cable on the caliper. The caliper is the main frame of the brakes that the brake pads are attached to. The brake cable is the thin cable extending off the caliper. Locate the bolt that's holding the brake cable. Use an Allen wrench to turn it counterclockwise a few times until the bolt is slightly loose.[8]- Don't unscrew the bolt all the way. Just rotate the Allen wrench counterclockwise 2-3 times until the bolt is loose.
-
Picture 9 of How to Adjust Bike Brakes Pull the brake cable outward to tighten it. Now that the bolt is loosened, you shouldn't have any problem pulling the cable. Hold it in place with your fingers once you've pulled it taut. As you pull the cable, the brake pads should tighten on the rim of the front tire. You want them to be tight enough that there's some resistance when you turn the tire, but not so tight that the tire isn't able to turn at all.[9]- If you can't turn the tire at all, pull less hard on the brake cable so it's not as tight.
-
Picture 10 of How to Adjust Bike Brakes Tighten the bolt holding the brake cable on the caliper. Use the Allen wrench and turn it clockwise 2-3 times until it won't turn anymore. The cable should be secure in place once the bolt is tightened. -
Picture 11 of How to Adjust Bike Brakes Tighten the barrel adjusters on the handlebars. Turn the barrel adjusters you loosened before clockwise several times until they're fully tightened. Tightening the barrel adjusters will loosen the brake pads that are clamped onto the front tire. Once the barrel adjusters are tightened, your brake cables should be all set!- Test the brake cables again by pulling the brake levers. When you pull the levers now, there should be 1 ½ inches (3.8 cm) between the lever and the grip on the handlebars.
Expert Advice
Use these techniques to avoid common mistakes when you're putting new brakes on your bike:
- Check the position of the wheel. Make sure you get the wheel it all the way into the dropouts of the fork on your bike frame. Otherwise, the brakes won't line up correctly.
- Make sure to close the quick release before you adjust your brakes. If the quick release is open on your bike and you don't realize it, you might think your brakes need to be adjusted when they don't.
- Make sure the rotor is next to the stationary pad if you have disc brakes. On most mechanical disc brakes, one brake pad sits next to the rotor, and the other pad moves and squeezes it all together. If you have the rotor next to the pad that moves, it will affect your braking performance, and your rotor will wind up getting bent.
Update 24 March 2020
You should read it
- Special cable, only a few countries in the world can produce it
- 10 milestones of regular maintenance help cars always in the best condition
- How to Keep Sports Bra Pads in Place
- Instructions on how to clean mouse pads at home in the simplest way
- How are APG and AAG cables different?
- These are the types of printer cables needed to connect to the computer
- 4 best USB-C cables 2019
- 13 unexpected facts about sea cable routes
- Map of 420 Internet cables, stretching 1.1 million kilometers on the seabed around the world
- A bill for phones using a common cable standard has been passed, iPhone is about to use USB-C cable?
- Which mouse pad should I buy? Detailed instructions on how to buy mouse pads
- How to connect a TV cable to multiple TVs
Maybe you are interested
Sprayers can kill insects, kill termites at the root? Guide to calling groups on Facebook Messenger computers 5 tips to help you get a high score in the History exam 10 interesting facts about taxi drivers you may not know yet Communication rules of true ladies, women should know 10 types of people you should avoid as far as possible in your life