Instructions for installing Mail Offline on MDaemon program.

Mail Offline is a system that operates based on the pre-installed Local Area Network (Local Area Network) model. In this network you do not need to have a dedicated server, but you only need to specify a machine with relative configuration to be the server (Mail Server), and the capacity of the hard disk must be enough to store the message , hard disk capacity must match the number of mail and the number of employees of your company. Please click here to refer to the general introduction about the network. I. Setting up and setting up parameters You must first have the software, this software you can download at (http://www.netcenter-vn.net/software), after completing the download, We start the installation. To install, just double click on the file you just downloaded (you run the * .bat file to merge the files). When you run the setup file, you will see the following interface (Figure 01): Figure 1 and the next step you just need to click on the Next button, the next interface will be (Figure 02) Figure 2 If you want to continue installing the program, you must accept the above conditions and you continue to click on the "I Agree To The Above" button to continue the installation process (Figure 03) Figure 3 The next step is to select the drive and folder that you want the program to install, the default Mail Deamon program will install in the MDeamon folder of drive C, in this step if you do not want to change the path. By default, you can click the Next button to continue the installation process, and if you want to change, you can click the Browse . button to specify the path of the program. We go through the next step as (Figure 04) the following illustration: Figure 4 in this step the program requires you to enter the registered name, or you are a trial user, you can enter arbitrarily in this step. Then continue with clicking the Next button (Figure 04). Figure 5 The next step is to leave the default configuration according to the program and continue to click Next (Figure 05) Figure 6 Now that the program will install automatically, please wait for a moment .. (Figure 06) After installing for a while, the program will switch to the same interface as above, in the program, the Primary DNS IP Address and Backup DNS IP Address entries are empty and you can fill in the same IP address as ( Figure 07) above. Once completed, you can click on Next to continue with the next interface Figure 8 Now you continue to select Finish that you have completed the installation process. : You must then Restart the machine to make sure that all program parameters are completely saved to the device. After your computer has restarted, you will see a white letter icon in the lower right corner of the screen. To proceed with the installation of the next parameters for the program, you move the cursor to this icon and right click you will see a black text called Open Mdeamon . you continue to select it . The first step is to enter the license key to register, go to Help and then select Register MDeamon, you can enter license key according to (Figure 9) the following illustration: Figure 9 After that you have to Restart the machine again to complete the registration. II. Setting Domain and POP parameters Now go to Setup in the Menu bar, select Primary Domain and select Domain / ISP tab (Figure 10) Figure 10 In this section, you will see the Domain name, here you will enter the domain name that you registered with the ISP. The HELO domain section you will also enter the domain name that you previously registered with the ISP. The Domain IP section of the program will automatically discover your IP. Part ISP / gateway host`s IP or domain name, you fill in 203.162.5.38, you select Send only undeliverable outbound mail to this host. Then click OK. III. Specify the processing / delivery time Next also in the setup section, select the Send / receive scheduler section to specify the schedule and time to process incoming and outgoing mail (Figure 11). Figure 11 Local / RAW / mail processing interval when you drag the slider to the right, the time will be 60 minutes, then the program will count down to 0 then the program will process the mail. You can drag the slider to specify your time (Figure 12). Figure 12 Also in the Setup section, find the RAS Dialup Settings section to tell the program which connection to use during mail processing. Check the Enable RAS dialup / dialdown engine check box (Figure 13). Figure 13 You select the ISP Logon Settings tab, in this section, check the box Use any currently active dialup session, or you will specify a fixed connection name by selecting the down arrow in the Use section. This RAS dialup profile lets you select the connection name you created earlier. Logon name and Logon password you type in the username and password you have registered (Figure 14) Figure 14 IV. Setting parameters for POP Next you select the DomainPOP mail collection section in Setup, in this section we will set the parameters for the program to know where to get mail (Figure 15) Figure 15 V. Creating a mail account, deleting, editing In the Accounts section, select Account Manager . you will see as (Figure 16) below: Figure 16 Now to create a new account you choose on New. Figure 17 In (Figure 17) the Real name section you can enter the full name of the user, POP / IMAP you will create the email address, in this section you enter the username, username@mycompany.com will be the real address in your company. You must select the Allow this account to be . item so that the user can use the mail client to send and receive mail. For example: Outlook Express, Internet Mail, . the Account password section, you can also set a password or leave it blank. VI. Delete mail address, edit information You also go to Accounts and you select Edit account or Delete account to edit, simply select the user name to delete and double click to return to Account Edit to edit the information about the location. letter or password.