How to Trim Spray Foam

Spray foam is really convenient for you to use since it expands to fill in gaps, but there may be times when you accidentally apply too much. If you have foam that bubbles out, it could have an unsightly appearance or make it difficult to...

Method 1 of 2:

Cutting Small Pieces of Spray Foam

Wait until the foam cures completely before trimming it. Check the curing time on the spray foam's packaging so you know how long it needs to set, which is usually between 12–24 hours. Allow the foam to expand completely and harden before you start working with it. Test the foam after 12 hours by seeing if it feels tacky. If the foam still feels a little sticky, leave it alone to cure until it has a hard, smooth finish.^{[1] X Research source}
1. Different brands of spray foam have different curing processes. Be sure to check the instructions for the one that you have.
Use a utility knife to score the edges of the foam if it's in a corner. If you sprayed foam into a corner of a wall or along a piece of trim, it may be more difficult to trim down. Place your utility knife on one side of the foam so it's flush against one side of the corner. Press the blade into the foam and slowly drag it along its length. Move your knife blade to the other side of the corner and make another cut through the foam so it falls off easier.^{[2] X Research source}
1. Be careful not to press the knife too deep into the foam since you could cut into the surface underneath it and cause damage.
2. Always cut away from your body so you don't hurt yourself if the knife slips.
Hold your utility knife on top of the foam so it's flush against the wall. Extend the blade so it's long enough to cut through the entire section of foam that's expanded out from the wall. Press the blade of your knife against the foam's top edge so it lays flat against the wall or surface.^{[3] X Research source}
1. Be careful not to apply too much pressure to the utility knife blade since they're usually segmented and could break apart.
Tip: If you don't have a utility knife that's long enough, you can use a flush-cut saw that has a flexible blade instead. You can buy them from your local hardware store.
Saw straight through the foam to remove the excess. Slowly guide your blade along the entire length of the foam piece you're cutting off. Try to keep the blade as flat against the wall as possible so you can remove the most foam. Keep slicing the foam off in small pieces until it's completely flush with the rest of the wall.^{[4] X Research source}
1. Throw away the excess pieces of spray foam with your regular trash.^{[5] X Research source}
Try using a metal scraper if you can't cut through the foam easily. Place the blade of your metal scraper against the top edge of the foam so it's flat against the surface. Apply a firm amount of pressure and push the scraper through the foam. Keep using sharp downward thrusts with the scraper to get rid of the foam.^{[6] X Research source}
1. Metal scrapers work best for rigid foam that's stuck on studs or are too large to cut with your knife. You can buy one from your local hardware store.
2. Be careful not to hold the metal scraper perpendicular to the surface, or else you may damage or cut into it.
Level the foam with the surface using a sanding block. Choose a fine sanding block so you smooth out the surface without leaving scratch marks. Go over the surface using small circular motions to smooth out any bits of foam that still stick out from the surface. Keep sanding until the foam looks perfectly flush with the surface so you're able to finish over it.^{[7] X Research source}
1. You can buy sanding blocks from your local hardware store.

Method 2 of 2:

Using a Foam Saw for Wall Insulation

Give the foam about 24 hours to harden and cure before cutting it. After spraying your foam, it will expand to fill in any small gaps before it starts to harden. Leave the spray foam alone for at least 24 hours so it has a chance to set. Test if the foam feels tacky, and if it does, allows it to continue curing until it has a hard, smooth finish.^{[8] X Trustworthy Source United States Environmental Protection Agency Independent U.S. government agency responsible for promoting safe environmental practices Go to source}
1. Avoid cutting the foam before it finishes curing since you could damage the entire treatment.
Warning: Spray foam insulation creates toxic fumes when it's applied and while it's curing. If you need to go back into the room before the foam cures, wear safety goggles, coveralls, disposable gloves, and a ventilator to stay protected.^{[9] X Trustworthy Source United States Environmental Protection Agency Independent U.S. government agency responsible for promoting safe environmental practices Go to source}
Rent a foam saw from your local hardware or equipment store. Foam saws are power tools that have long, flexible blades so you can cut all of the foam that extends past your wall studs. Contact a few local hardware or equipment supply stores to see if they have a foam saw that you can rent for the day. Compare the rates and choose the option that you can best afford.
1. If you have a reciprocating saw, you may be able to find blades made to cut through spray foam so you don't have to buy a separate tool.
Choose the saw blade meant for the type of cell structure your foam has. Your spray foam will either have an open-cell or closed-cell structure, which determines how well it blocks water and air. If you're using indoor foam that's open-cell, it will be easier to work with since it doesn't harden completely. Closed-cell foam completely blocks water and air and gets more rigid, so it will cause more friction on your saw. Pick the appropriate saw blade for the foam you used before screwing it into the saw.^{[10] X Research source}
1. You can buy foam saw blades online or at your local hardware store.
2. Avoid using the wrong type of blade on your foam since you could damage the saw or the insulation.
3. Foam saw blades are usually around 18–27 inches (46–69 cm) long.
Hold the blade of the foam saw flush against the wall studs. Position the blade so it spans across 2 wall studs so you can level off the foam between them. Start at the top of your wall so the pieces fall down easily as you cut them. Keep the blade as flat against the studs as possible so you make the cleanest cut.^{[11] X Research source}
1. Keep your saw turned off while you're positioning the blade so you don't accidentally cut or damage anything.
Guide the saw down the height of the wall to cut the foam. Hold the handles on the side and back of the saw to stabilize it before pulling the trigger to turn it on. Slowly move the blade down the wall, making sure it stays tightly against the studs. When you reach the bottom of the wall, let go of the trigger to stop the saw and let the foam pieces fall down.^{[12] X Research source}
1. You do not need to wear goggles or a ventilator when you're working with cured foam.
2. Dispose of the foam pieces along with your regular garbage.
3. Be extremely careful when working with your saw since you could easily cut yourself and cause serious injury.
Continue trimming the foam from the rest of your walls. Reposition the blade at the top of the wall between the next 2 studs. Pull the trigger and work your way back down toward the floor to remove all of the foam. Keep trimming back the foam between each of the studs so it's flush with them.^{[13] X Research source}