HomeTech info

How to Do a Burnout on a Motorcycle

Part 1 of 2:

Applying the Brake

  1. How to Do a Burnout on a Motorcycle Picture 1
    Stand with both feet as flat on the ground as possible. To prevent the tires from gaining traction, put the least amount of weight on the bike by standing over the bike. If the tires have too much traction, then the motorcycle will move forward when you attempt a burnout.[1]
  2. How to Do a Burnout on a Motorcycle Picture 2
    Start the motorcycle and keep it in the neutral gear. Turn the key in the ignition and start up the engine so it can warm up. Check the temperature gauge after a few minutes to make sure the dial is at about the halfway point to indicate that the engine has warmed up.[2]
    1. Keep the engine in the neutral gear while it warms up.
    2. You can rev the engine a few times to get it warmer faster.
    3. Allow the engine to run for at least 5 minutes before you attempt a burnout.

    Warning: It's dangerous to perform a burnout with a cold engine because it can sputter and suddenly gain traction, causing the motorcycle to lurch forward.

  3. How to Do a Burnout on a Motorcycle Picture 3
    Pull the clutch lever all the way in. On most motorcycles, the clutch is the lever on the left hand of the handlebars. Use all 4 fingers to engage the clutch by pulling it back all the way to the handlebar.[3]
    1. Keep a tight grip on the clutch lever so it stays engaged.
    2. If your motorcycle has the clutch on the right handlebar, be sure to engage it fully with all 4 fingers of your right hand.
  4. How to Do a Burnout on a Motorcycle Picture 4
    Hold the front brake with the middle finger of your right hand. Apply the brake and rev the engine throttle simultaneously by holding the front brake with your right hand. Use just your middle finger to pull back the lever for the brake so you can use the rest of your hand to work the throttle.[4]
    1. If you have a motorcycle with the throttle on the left-hand side, then use the middle finger of your left hand to apply the brake.
Part 2 of 2:

Releasing the Clutch

  1. How to Do a Burnout on a Motorcycle Picture 5
    Put the motorcycle into first gear. Use your foot to click the gear shift pedal so the motorcycle shifts into first gear. Keep the clutch engaged with your left hand so the motorcycle doesn't shift into gear yet.[5]
  2. How to Do a Burnout on a Motorcycle Picture 6
    Rev up the engine close to the red line on the gauge. With your right hand, rev up the engine by twisting the throttle down. Look at the repetitions per minute (RPM) gauge and look for the red line towards the top of it. Rev up the engine so the arrow is about 75% of the way to the red line at the top.[6]
    1. Start revving the engine slowly to make sure the engine isn't in gear and the bike won't move.
    2. It's important that you build up the engine before you put it into gear so the tire spins too fast to gain traction.
  3. How to Do a Burnout on a Motorcycle Picture 7
    Lean forward slightly to shift all of the weight off of the rear tire. Make sure your feet are flat and you're standing stable. To make sure that all of the weight is off of the rear tire, lean forward a little bit.[7]
  4. How to Do a Burnout on a Motorcycle Picture 8
    Let go of the clutch to perform a burnout. Don't ease off of the clutch to disengage it. Instead, let it go in 1 motion by releasing all of your fingers at once. The engine will then engage in first gear and the rear tire will start spinning to create a burnout.[8]
    1. The longer you hold the burnout, the more wear and tear on your rear tire.

    Tip: Hold the burnout for a minute to create a plume of smoke.

  5. How to Do a Burnout on a Motorcycle Picture 9
    Reengage the clutch and release the throttle to end the burnout. Use your left hand to pull the lever to engage the clutch, which will pull the engine out of first gear and into neutral. Rollback the throttle with your right hand, but keep the brake engaged the entire time. The rear tire will come to a stop and your motorcycle will not roll forward.[9]
    1. Do not release the brake until the tire has completely stopped spinning.
4.5 ★ | 2 Vote
enginehandclutchgear

You should read it

May be interested

  • Burnout from Work? 7 Research-Backed Strategies To RecoverBurnout from Work? 7 Research-Backed Strategies To Recover
    if you are experiencing burnout from work, here are 7 research-backed strategies to help you recover and get your life back.
  • Ride a motorcycle with a mobile applicationRide a motorcycle with a mobile application
    grabbike is a motorcycle taxi service that directly connects customers and drivers through smartphones and this is an extension of grabtaxi application in vietnam.
  • How to Get a Motorcycle License in NevadaHow to Get a Motorcycle License in Nevada
    there are currently a number of ways to obtain a motorcycle license in the state of nevada depending on your unique situation. if you are new to driving motorcycles, you must either pass a knowledge and skills test at your local department...
  • As you know, why is the leaning leg of the motorcycle on the left?As you know, why is the leaning leg of the motorcycle on the left?
    even though we ride a motorbike every day, most of us do not understand the car we still use, specifically why the vehicle's inclined leg is on the left side? let's find the answer to this question!
  • How to Ride a Motorcycle (Beginners)How to Ride a Motorcycle (Beginners)
    learning to ride a motorcycle can be fun. the best way to learn how to properly ride is in a safe and controlled manner. always practice safety first and be sure you have appropriate safety gear for the type of riding you will do....
  • How to Ride a Motorcycle with a PassengerHow to Ride a Motorcycle with a Passenger
    riding a motorcycle with a passenger requires more balance and control than riding solo. make sure you are completely comfortable and confident riding a motorcycle by yourself before you attempt to do so with a passenger. once you're ready...
  • How to Prepare to Compete in a Motorcycle Road RaceHow to Prepare to Compete in a Motorcycle Road Race
    motorcycle road races can be very fun to participate in. however, you need to take the proper steps to prepare, legally and by developing your skills, or they can be very dangerous. anyone can become a licensed rider and compete in a race...
  • How to Shift Gears on a MotorcycleHow to Shift Gears on a Motorcycle
    one of the most important processes of riding a motorcycle is shifting gears. this may seem like a challenge to master, but shifting gears is really a simple process. how you shift gears, however, will depend on whether your motorcycle has...
  • Top 5 best kits for professional car mechanicsTop 5 best kits for professional car mechanics
    if you are looking for the best home and workshop for your family, follow the top 5 products below. surely they will be extremely ideal suggestions for you.
  • How to Ride a MotorcycleHow to Ride a Motorcycle
    motorcycles are fun vehicles that allow you to experience the open road. however, it's critical that you learn to ride in a controlled and safe way. take a motorcycle safety course and get a permit or license if it is required in your...

Tech info